add aneta8 printer.cfg
This commit is contained in:
commit
b0b6eb8e56
183
aneta8/printer.cfg
Normal file
183
aneta8/printer.cfg
Normal file
@ -0,0 +1,183 @@
|
||||
# This file contains common pin mappings for RAMPS (v1.3 and later)
|
||||
# boards. RAMPS boards typically use a firmware compiled for the AVR
|
||||
# atmega2560 (though other AVR chips are also possible).
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
[stepper_x]
|
||||
step_pin: ar54
|
||||
dir_pin: ar55
|
||||
enable_pin: !ar38
|
||||
microsteps: 16
|
||||
rotation_distance: 32
|
||||
endstop_pin: ^!ar3
|
||||
position_endstop: -39
|
||||
position_min: -39
|
||||
position_max: 238
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2130 stepper_x]
|
||||
cs_pin: ar59
|
||||
run_current: 0.5
|
||||
hold_current: 0.3
|
||||
stealthchop_threshold: 99999
|
||||
|
||||
[stepper_y]
|
||||
step_pin: ar60
|
||||
dir_pin: ar61
|
||||
enable_pin: !ar56
|
||||
microsteps: 16
|
||||
rotation_distance: 32
|
||||
endstop_pin: ^!ar14
|
||||
position_endstop: -10
|
||||
position_min: -10
|
||||
position_max: 260
|
||||
homing_speed: 50
|
||||
|
||||
[tmc2130 stepper_y]
|
||||
cs_pin: ar63
|
||||
run_current: 0.5
|
||||
hold_current: 0.3
|
||||
stealthchop_threshold: 99999
|
||||
|
||||
[stepper_z]
|
||||
step_pin: ar46
|
||||
dir_pin: !ar48
|
||||
enable_pin: !ar62
|
||||
microsteps: 16
|
||||
rotation_distance: 8
|
||||
endstop_pin: probe:z_virtual_endstop
|
||||
position_min: -2
|
||||
position_max: 200
|
||||
|
||||
[tmc2130 stepper_z]
|
||||
cs_pin: ar40
|
||||
run_current: 0.5
|
||||
hold_current: 0.3
|
||||
stealthchop_threshold: 99999
|
||||
|
||||
[probe]
|
||||
pin: !ar18
|
||||
x_offset: -28
|
||||
y_offset: -50
|
||||
z_offset: 1.080
|
||||
|
||||
[safe_z_home]
|
||||
home_xy_position: 128,150
|
||||
z_hop: 10
|
||||
|
||||
[bed_mesh]
|
||||
speed: 60
|
||||
horizontal_move_z: 5
|
||||
mesh_min: 10, 10
|
||||
mesh_max: 200, 170
|
||||
probe_count: 5,5
|
||||
relative_reference_index: 12
|
||||
|
||||
[extruder]
|
||||
step_pin: ar26
|
||||
dir_pin: ar28
|
||||
enable_pin: !ar24
|
||||
microsteps: 16
|
||||
rotation_distance: 33.500
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: ar10
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: analog13
|
||||
min_temp: 5
|
||||
max_temp: 275
|
||||
|
||||
[tmc2130 extruder]
|
||||
cs_pin: ar42
|
||||
run_current: 0.5
|
||||
hold_current: 0.3
|
||||
stealthchop_threshold: 99999
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: ar8
|
||||
sensor_type: ATC Semitec 104GT-2
|
||||
sensor_pin: analog14
|
||||
min_temp: 5
|
||||
max_temp: 130
|
||||
|
||||
[fan]
|
||||
pin: ar9
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
|
||||
pin_map: arduino
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 400
|
||||
max_accel: 500
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 80
|
||||
|
||||
# Common EXP1 / EXP2 (display) pins
|
||||
[board_pins]
|
||||
aliases:
|
||||
# Common EXP1 header found on many "all-in-one" ramps clones
|
||||
EXP1_1=ar37, EXP1_3=ar17, EXP1_5=ar23, EXP1_7=ar27, EXP1_9=<GND>,
|
||||
EXP1_2=ar35, EXP1_4=ar16, EXP1_6=ar25, EXP1_8=ar29, EXP1_10=<5V>,
|
||||
# EXP2 header
|
||||
EXP2_1=ar50, EXP2_3=ar31, EXP2_5=ar33, EXP2_7=ar49, EXP2_9=<GND>,
|
||||
EXP2_2=ar52, EXP2_4=ar53, EXP2_6=ar51, EXP2_8=ar41, EXP2_10=<RST>
|
||||
# Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi"
|
||||
# Note, some boards wire: EXP2_8=<RST>, EXP2_10=ar41
|
||||
|
||||
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
||||
|
||||
#*# <---------------------- SAVE_CONFIG ---------------------->
|
||||
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
||||
#*#
|
||||
#*# [extruder]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 21.047
|
||||
#*# pid_ki = 0.835
|
||||
#*# pid_kd = 132.598
|
||||
#*#
|
||||
#*# [heater_bed]
|
||||
#*# control = pid
|
||||
#*# pid_kp = 68.198
|
||||
#*# pid_ki = 1.249
|
||||
#*# pid_kd = 930.898
|
||||
#*#
|
||||
#*# [bed_mesh default]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.127500, 0.090000, -0.000000, -0.142500, -0.145000
|
||||
#*# 0.157500, 0.060000, -0.050000, -0.127500, -0.180000
|
||||
#*# 0.175000, 0.087500, 0.000000, -0.122500, -0.150000
|
||||
#*# 0.200000, 0.152500, 0.032500, -0.090000, -0.132500
|
||||
#*# 0.232500, 0.175000, 0.060000, -0.067500, -0.092500
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 10.0
|
||||
#*# algo = lagrange
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 10.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 170.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 200.0
|
||||
#*#
|
||||
#*# [bed_mesh hot]
|
||||
#*# version = 1
|
||||
#*# points =
|
||||
#*# 0.127500, 0.090000, -0.000000, -0.142500, -0.145000
|
||||
#*# 0.157500, 0.060000, -0.050000, -0.127500, -0.180000
|
||||
#*# 0.175000, 0.087500, 0.000000, -0.122500, -0.150000
|
||||
#*# 0.200000, 0.152500, 0.032500, -0.090000, -0.132500
|
||||
#*# 0.232500, 0.175000, 0.060000, -0.067500, -0.092500
|
||||
#*# tension = 0.2
|
||||
#*# min_x = 10.0
|
||||
#*# algo = lagrange
|
||||
#*# y_count = 5
|
||||
#*# mesh_y_pps = 2
|
||||
#*# min_y = 10.0
|
||||
#*# x_count = 5
|
||||
#*# max_y = 170.0
|
||||
#*# mesh_x_pps = 2
|
||||
#*# max_x = 200.0
|
||||
Loading…
x
Reference in New Issue
Block a user