184 lines
3.9 KiB
INI
184 lines
3.9 KiB
INI
# This file contains common pin mappings for RAMPS (v1.3 and later)
|
|
# boards. RAMPS boards typically use a firmware compiled for the AVR
|
|
# atmega2560 (though other AVR chips are also possible).
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: ar54
|
|
dir_pin: ar55
|
|
enable_pin: !ar38
|
|
microsteps: 16
|
|
rotation_distance: 32
|
|
endstop_pin: ^!ar3
|
|
position_endstop: -39
|
|
position_min: -39
|
|
position_max: 238
|
|
homing_speed: 50
|
|
|
|
[tmc2130 stepper_x]
|
|
cs_pin: ar59
|
|
run_current: 0.5
|
|
hold_current: 0.3
|
|
stealthchop_threshold: 99999
|
|
|
|
[stepper_y]
|
|
step_pin: ar60
|
|
dir_pin: ar61
|
|
enable_pin: !ar56
|
|
microsteps: 16
|
|
rotation_distance: 32
|
|
endstop_pin: ^!ar14
|
|
position_endstop: -10
|
|
position_min: -10
|
|
position_max: 260
|
|
homing_speed: 50
|
|
|
|
[tmc2130 stepper_y]
|
|
cs_pin: ar63
|
|
run_current: 0.5
|
|
hold_current: 0.3
|
|
stealthchop_threshold: 99999
|
|
|
|
[stepper_z]
|
|
step_pin: ar46
|
|
dir_pin: !ar48
|
|
enable_pin: !ar62
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: probe:z_virtual_endstop
|
|
position_min: -2
|
|
position_max: 200
|
|
|
|
[tmc2130 stepper_z]
|
|
cs_pin: ar40
|
|
run_current: 0.5
|
|
hold_current: 0.3
|
|
stealthchop_threshold: 99999
|
|
|
|
[probe]
|
|
pin: !ar18
|
|
x_offset: -28
|
|
y_offset: -50
|
|
z_offset: 1.080
|
|
|
|
[safe_z_home]
|
|
home_xy_position: 128,150
|
|
z_hop: 10
|
|
|
|
[bed_mesh]
|
|
speed: 60
|
|
horizontal_move_z: 5
|
|
mesh_min: 10, 10
|
|
mesh_max: 200, 170
|
|
probe_count: 5,5
|
|
relative_reference_index: 12
|
|
|
|
[extruder]
|
|
step_pin: ar26
|
|
dir_pin: ar28
|
|
enable_pin: !ar24
|
|
microsteps: 16
|
|
rotation_distance: 33.500
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: ar10
|
|
sensor_type: ATC Semitec 104GT-2
|
|
sensor_pin: analog13
|
|
min_temp: 5
|
|
max_temp: 275
|
|
|
|
[tmc2130 extruder]
|
|
cs_pin: ar42
|
|
run_current: 0.5
|
|
hold_current: 0.3
|
|
stealthchop_threshold: 99999
|
|
|
|
[heater_bed]
|
|
heater_pin: ar8
|
|
sensor_type: ATC Semitec 104GT-2
|
|
sensor_pin: analog14
|
|
min_temp: 5
|
|
max_temp: 130
|
|
|
|
[fan]
|
|
pin: ar9
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
|
|
pin_map: arduino
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 400
|
|
max_accel: 500
|
|
max_z_velocity: 5
|
|
max_z_accel: 80
|
|
|
|
# Common EXP1 / EXP2 (display) pins
|
|
[board_pins]
|
|
aliases:
|
|
# Common EXP1 header found on many "all-in-one" ramps clones
|
|
EXP1_1=ar37, EXP1_3=ar17, EXP1_5=ar23, EXP1_7=ar27, EXP1_9=<GND>,
|
|
EXP1_2=ar35, EXP1_4=ar16, EXP1_6=ar25, EXP1_8=ar29, EXP1_10=<5V>,
|
|
# EXP2 header
|
|
EXP2_1=ar50, EXP2_3=ar31, EXP2_5=ar33, EXP2_7=ar49, EXP2_9=<GND>,
|
|
EXP2_2=ar52, EXP2_4=ar53, EXP2_6=ar51, EXP2_8=ar41, EXP2_10=<RST>
|
|
# Pins EXP2_1, EXP2_6, EXP2_2 are also MISO, MOSI, SCK of bus "spi"
|
|
# Note, some boards wire: EXP2_8=<RST>, EXP2_10=ar41
|
|
|
|
# See the sample-lcd.cfg file for definitions of common LCD displays.
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [extruder]
|
|
#*# control = pid
|
|
#*# pid_kp = 21.047
|
|
#*# pid_ki = 0.835
|
|
#*# pid_kd = 132.598
|
|
#*#
|
|
#*# [heater_bed]
|
|
#*# control = pid
|
|
#*# pid_kp = 68.198
|
|
#*# pid_ki = 1.249
|
|
#*# pid_kd = 930.898
|
|
#*#
|
|
#*# [bed_mesh default]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.127500, 0.090000, -0.000000, -0.142500, -0.145000
|
|
#*# 0.157500, 0.060000, -0.050000, -0.127500, -0.180000
|
|
#*# 0.175000, 0.087500, 0.000000, -0.122500, -0.150000
|
|
#*# 0.200000, 0.152500, 0.032500, -0.090000, -0.132500
|
|
#*# 0.232500, 0.175000, 0.060000, -0.067500, -0.092500
|
|
#*# tension = 0.2
|
|
#*# min_x = 10.0
|
|
#*# algo = lagrange
|
|
#*# y_count = 5
|
|
#*# mesh_y_pps = 2
|
|
#*# min_y = 10.0
|
|
#*# x_count = 5
|
|
#*# max_y = 170.0
|
|
#*# mesh_x_pps = 2
|
|
#*# max_x = 200.0
|
|
#*#
|
|
#*# [bed_mesh hot]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.127500, 0.090000, -0.000000, -0.142500, -0.145000
|
|
#*# 0.157500, 0.060000, -0.050000, -0.127500, -0.180000
|
|
#*# 0.175000, 0.087500, 0.000000, -0.122500, -0.150000
|
|
#*# 0.200000, 0.152500, 0.032500, -0.090000, -0.132500
|
|
#*# 0.232500, 0.175000, 0.060000, -0.067500, -0.092500
|
|
#*# tension = 0.2
|
|
#*# min_x = 10.0
|
|
#*# algo = lagrange
|
|
#*# y_count = 5
|
|
#*# mesh_y_pps = 2
|
|
#*# min_y = 10.0
|
|
#*# x_count = 5
|
|
#*# max_y = 170.0
|
|
#*# mesh_x_pps = 2
|
|
#*# max_x = 200.0
|